XIB-E【PDF 24/64 页】BOARD INTERFACE ETHERNET

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录58

20页 21页 22页 23页 [24页]25页 26页 27页 28页

XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>

DR (DI3 Configuration) Command

AT Command: ATDR

Binary Command: 0x2D (45 decimal)

Parameter Range: 0 4

Parameter

Configuration

Disabled

DI3 I/O passing enabled

Connect on low

Disconnect on high

Connect and Disconnect

Default Parameter Value: 0

Number of bytes returned: 1

Related Commands: CD (DO3 Configuration),

CO (DO3 Timeout), MD (RF Mode)

Minimum Firmware Version Required: 4.30

<Serial Interfacing> DR Command is used to

configure DI3 (pin 2, SLEEP) for I/O line passing

(use with CD = 1 or 2 and CO) or controlling

connection status (use with MD = 1 or 2).

DT (Destination Address) Command

<Networking & Security> DT Command is used

to set the networking address of an XStream

Module. XStream Modules use three filtration

layers: Channels (ATHP), Vendor Identification

Number (ATID) and Destination Addresses

(ATDT). DT Command assigns an address to a

module that enables it to communicate only with

other modules having the same addresses. All

modules that share the same Destination Address can communicate freely with each other.

Modules in the same network with a different Destination Address (than that of the transmitter)

will listen to all transmissions to stay synchronized, but will not send any of the data out their

serial ports.

AT Command: ATDT

Binary Command: 0x00

Parameter Range: 0 0xFFFF

Default Parameter Value: 0

Number of bytes returned: 2

Related Commands: HP (Hopping Channel), ID

(Module VID), MK (Address Mask)

E0 (Echo Off) Command

AT Command: ATE0

Binary Command: 0x0A (10 decimal)

<Command Mode Options> The E0 command

turns off character echo in AT Command Mode.

By default, echo is off.

E1 (Echo On) Command

AT Command: ATE1

Binary Command: 0x0B (11 decimal)

<Command Mode Options> E1 Command turns

on the echo in AT Command Mode. Each typed

character will be echoed back to the terminal

when ATE1 is active. E0 is the default.

ER (Receive Error Count) Command

<Diagnostics> Set/Read the receive error count.

The error-count records the number of packets

partially received then aborted on reception

error. This value returns to 0 after a reset and is

not non-volatile (value does not persist in the

modules memory after a power-up sequence).

Once the receive error count reaches its

maximum value (up to 0xFFFF), it remains at its maximum count value until the maximum count

value is explicitly changed or the module is reset.

AT Command: ATER

Binary Command: 0x0F (15 decimal)

Parameter Range: 0 0xFFFF

Default Parameter Value: 0

Number of bytes returned: 2

Related Commands: GD (Receive Good Count)

牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>

24?/DIV>

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式